色婷婷久久综合中文久久蜜桃AV,亚洲Aⅴ无码一区二区二三区软件,亚洲AⅤ综合在线欧美一区,久久精品亚洲中文字幕无码麻豆,师父的蘑菇好软水好多H15视频,久久午夜夜伦鲁鲁片无码免费播放区,啦啦啦在线观看视频免费观看,亚洲毛片视频一级,久久国产精品久久国产精品,欧美三级一区二区三区在线观看

Technical document

How much does the wall thickness of plastic parts affect the product?

2024-10-21 16:43:10 The wall thickness of plastic parts

The wall thickness of plastic parts has a significant influence on product quality.

First, mechanical properties

Step 1: Intensity

Adequate wall thickness provides sufficient strength. If the wall thickness is too thin, plastic parts are prone to rupture 

and deformation when subjected to external forces. For example, in some plastic containers that need to withstand a 

certain pressure, insufficient wall thickness may cause the container to break during filling or transportation, affecting 

the performance and safety of the product. The wall thickness is too thick, although the strength has increased, but it 

may lead to internal stress concentration, so that the plastic parts in the cooling process of warping, shrinkage and other 

defects, will also reduce the quality of the product.

2. Rigidity

Reasonable wall thickness helps to improve the rigidity of plastic parts. When the wall thickness is too thin, the plastic 

parts are easy to bend and deform, which affects the dimensional stability and assembly accuracy. For example, in the plastic 

housing of some precision instruments, insufficient wall thickness may cause the housing to fail to provide adequate support 

for the internal components, affecting the performance and reliability of the instrument.

However, the wall thickness is too thick may also make the plastic parts too heavy, increase the weight and cost of the product, 

and may also affect the appearance quality of the product. Therefore, it is very important to reasonably determine the wall 

thickness of the plastic parts. Points to note are as follows:

a, the wall thickness of plastic parts should be as uniform as possible, to avoid too thin, too thick and wall thickness mutation, 

if the plastic parts require a change in wall thickness, should use a gradual or circular transition, otherwise it will cause uneven 

shrinkage of plastic parts deformation, affect the strength of plastic parts, affect the flow of injection molding process problems.

b, the wall thickness of plastic parts is generally in the range of 1-5mm. The most commonly used value is 2-3mm.

c, the minimum wall thickness of commonly used plastic parts and the recommended value of commonly used wall thickness: (mm)

d, try not to design the reinforcement and screw column too thick, it is generally recommended to take half of the thickness 

of the body wall is safer, otherwise it is easy to cause appearance problems such as miniature

e, try not to design the parts into a separate plate, the size is very small, otherwise the deformation will lead to uneven parts


injection mould

injection mould

Second, molding process

1. Injection molding

During the injection molding process, the wall thickness has an important effect on the molding cycle, shrinkage rate and other 

parameters. When the wall thickness is too thin, the flow resistance of the plastic melt in the mold increases, the filling is difficult, 

and the defects such as short shot and lack of material are easy to appear. This will not only affect the appearance quality of the 

product, but may also reduce the strength and performance of the product.

If the wall thickness is too thick, the cooling time will be extended, the molding cycle will be increased, and the production 

efficiency will be reduced. At the same time, the thick wall part is easy to produce uneven cooling phenomenon, resulting in 

increased internal stress, shrinkage holes, shrinkage marks and other defects.

2. Blow molding

For blow molded plastic parts, the uniformity of wall thickness is very important. Uneven wall thickness will lead to uneven 

force in the blowing process of plastic parts, easy to crack, deformation and other problems.

Reasonable wall thickness design can ensure uniform expansion of plastic parts in the blow molding process, improve product 

quality and production efficiency.

Third, appearance quality

1. Surface flatness

The uneven wall thickness will cause the plastic parts to shrink inconsistently during the cooling process, resulting in uneven 

surface phenomena and affecting the appearance quality of the product. Especially for some plastic parts with high appearance 

requirements, such as automotive interior parts, electronic product shells, etc., the uniformity of wall thickness is directly related 

to the grade and market competitiveness of the product.

2. Gloss

The wall thickness also has a certain influence on the gloss of plastic parts. In general, the surface gloss of plastic parts with 

moderate wall thickness is better, and the wall thickness is too thin or too thick may lead to a decrease in gloss. This is because 

when the wall thickness is too thin, the flow speed of the plastic melt in the mold is faster, and the surface is easy to produce a 

rough phenomenon; When the wall thickness is too thick, the cooling time is extended, and the crystallinity of the plastic 

molecules is increased, which will also affect the surface gloss.

Fourth, the cost factor

1. Material cost

Too thick wall thickness will increase the amount of material used in plastic parts, thereby increasing the cost of the product. 

Under the premise of meeting the performance requirements of the product, the wall thickness should be minimized to reduce 

the material cost.

2. Processing cost

Wall thickness also has an impact on processing costs. When the wall thickness is too thin, the processing difficulty is increased, 

and higher injection pressure and speed are required, which increases the energy consumption and wear of the equipment, 

thus increasing the processing cost. The wall thickness is too thick will prolong the molding cycle, reduce production efficiency, 

and also increase the processing cost.

injection mould


Home
Product
News
Contact
伊人久久大香线蕉AV波多野结衣| 色网人人妻人人爽人人添夜夜夜| 国产片AV不卡在线观看| 熟妇人妻无乱码中文字幕真矢织江| 91香蕉国产亚洲一区二区三区| 巨胸美女露双奶头无遮挡一丝网站 | 国产真实老熟女无套内谢妓女| 亚洲第一无码精品一区| 久久亚洲国产成人精品性色| 国产精品成人嫩草影院| 91久久精品日日躁夜夜躁欧美| 亚洲中文久久久久久精品| 精品无人区无码乱码大片国产| 热99re久久精品国产99热| 欧美精品久久天天躁_天堂8在线天堂资源BT| 无码成人AV片在线在线播放| 人妻无码中文专区久久AV| 无码精品人妻一区二区三区涩爱 | 亚洲AV蜜桃永久无码精品| 久久丫精品国产亚洲AV| 无码人妻精品一区二区三区久久久| 日木亚洲精品无码专区| 制服丝袜人妻中文字幕在线| 国产SUV精品一区二区88L| 欧美又大粗又爽又黄大片视频| 女人高潮被爽到呻吟在线观看| 日韩人妻无码专区综合网| 国产精品日本亚洲777| 欧美巨大XXXX做受l色诱久久av| 妖精色AV无码国产在线看| 国产AV无码专区亚洲A∨毛片| 成人va在线一区二区三区四区| 精品多毛少妇人妻AV免费久久| 国产无人区卡一卡二卡三乱码网站| 成人精品一区二区户外勾搭野战| 国产福利一区二区三区| 欧美在线成人午夜影视| 欧美日韩不卡中文字幕在线| 精品人妻少妇一区二区三区不卡| 久久水蜜桃亚洲av无码精品麻豆| 无码AV中文一区二区三区桃花岛|